Post by SandStorm on Apr 16, 2006 19:54:44 GMT
WARNING! We are not responsible by any damage that could happen, you MUST have full of PATIENCE and CARE while doing this.
1-> First of all:
We need to remove everything from the SX1 (SIM card, MMC, Battery and the Battery cover, of course)
2-> Remove the screws w\ Torx no5, and when all of them are out, you'll see one open part.
3-> Slide your SIM card (Be carefull, do not use the part that have the chip!!!) into the openpart between the front and the middle covers and try to push out the front cover carefully.
Also do the same to the other side to remove it without break.
4-> Its time to remove the antena cover. It is clued, so be careful.
Use one thinny screwdriver to pull it out, then, push into the cover carefully to take it out.
5-> If got the the double-tape (glue on the two sides) with your cover cut it, and put on your new antenna cover
6-> It's time to the worst part. Remove the keypad, speaker, IrDA, etc from the original front cover to the new one. The IrDA, and speaker is very easu, but the keypad needs a lot of patiente and care.
7-> Remove the keypad clips (marked w\ arrows),
8-> remove this "key row". Here's one, which these are fastened with six clips. But to really solve one needs only the three.
We can this three clips.
9-> Then look at the image to see how to remove it. You can use one screwdriver to take it out.
Remember, CAREFULLY!
10-> Now, do the reverse, and don't forgett to put the rubber moldure in the new case, otherwise, your screen will be full of SAND and DUST!
You don't want one sandstorm inside it, don't you?
11-> Okitoky after moving all the stuff (keys, IrDA, speaker) it must look like this:
12-> Then, assemble all the things (in the reverse order) and when done, will look like that:
13-> Done! Now buy me a coke! NOW!!!! :twisted:
[NOTE! This tutorial is based on Gandalf's tutorial (from siemens-mobiles.org), the speeches are different, but the images are the same.]
1-> First of all:
We need to remove everything from the SX1 (SIM card, MMC, Battery and the Battery cover, of course)
2-> Remove the screws w\ Torx no5, and when all of them are out, you'll see one open part.
3-> Slide your SIM card (Be carefull, do not use the part that have the chip!!!) into the openpart between the front and the middle covers and try to push out the front cover carefully.
Also do the same to the other side to remove it without break.
4-> Its time to remove the antena cover. It is clued, so be careful.
Use one thinny screwdriver to pull it out, then, push into the cover carefully to take it out.
5-> If got the the double-tape (glue on the two sides) with your cover cut it, and put on your new antenna cover
6-> It's time to the worst part. Remove the keypad, speaker, IrDA, etc from the original front cover to the new one. The IrDA, and speaker is very easu, but the keypad needs a lot of patiente and care.
7-> Remove the keypad clips (marked w\ arrows),
8-> remove this "key row". Here's one, which these are fastened with six clips. But to really solve one needs only the three.
We can this three clips.
9-> Then look at the image to see how to remove it. You can use one screwdriver to take it out.
Remember, CAREFULLY!
10-> Now, do the reverse, and don't forgett to put the rubber moldure in the new case, otherwise, your screen will be full of SAND and DUST!
You don't want one sandstorm inside it, don't you?
11-> Okitoky after moving all the stuff (keys, IrDA, speaker) it must look like this:
12-> Then, assemble all the things (in the reverse order) and when done, will look like that:
13-> Done! Now buy me a coke! NOW!!!! :twisted:
[NOTE! This tutorial is based on Gandalf's tutorial (from siemens-mobiles.org), the speeches are different, but the images are the same.]